Mechanical properties of metaphyseal bone in the proximal femur

doi:10.1016/0021-9290(91)90350-V

Journal of Biomechanics

Volume 24, Issue 5, 1991, Pages 317-325, 327-329

https://doi.org/10.1016/0021-9290(91)90350-V Get rights and content

Abstract

We used a three-point bending test to investigate the structural behavior of 123 rectangular flat plate specimens harvested from the metaphyseal shell of the cervical and intertrochanteric regions of five fresh/frozen human proximal femora. For comparison purposes, 36 specimens of similar geometry were also fabricated from bone of the femoral diaphysis. All specimens were oriented in either the local longitudinal or transverse directions. The mean longitudinal elastic modulus was 9650 ± 2410 (SD) MPa and demonstrated a 24% decrease from that measured for the diaphysis (12500 ± 2140 MPa) using the same testing technique. However, the transverse elastic moduli did not differ significantly between the proximal (5470 ± 1720 MPa) and diaphyseal (5990 ± 1520 MPa) specimens. The globally averaged values for the ultimate tensile strengths of the metaphyseal shell were 101 ± 26 MPa in the longitudinal and 50 ± 12 MPa in the transverse directions. These compared with diaphyseal values of 128 ± 16 MPa and 47 ± 12 MPa, respectively. While these differences were largely due to the reduced density of the proximal specimens, a slight decrease in transverse anisotropy for the proximal specimens was also noted by comparing the ratio of longitudinal to transverse moduli (1.76) and tensile strength (2.02) to the diaphyseal values (2.09 and 2.71, respectively). Use of these data should lead to improved performance of analytical models for the proximal femur, and thus help focus increased attention on the structural contributions of trabecular bone to the strength and rigidity of the proximal femur.

References (17)

S.F. Lipson et al.
The relationship between elastic properties and microstructure of bovine cortical bone
J. Biomechanics
(1984)
D.T. Reilly et al.
The elastic and ultimate properties of compact bone tissue
J. Biomechanics
(1975)
I.N. Bronshtein et al.
T.D. Brown et al.
The apparent elastic modulus of the juxtarticular subchondral bone of the femoral head
J. Orthop. Res.
(1984)
A.H. Burstein et al.
Aging of bone tissue: mechanical properties
J. Bone Jt Surg. (Am)
(1976)
K. Choi et al.
The elastic modulus of trabecular, subchondral, and cortical bone tissue
Trans. 35th ORS
(1989)
S.C. Cowin
The mechanical properties of cortical bone tissue
J.D. Currey et al.
Tensile yield in bone
Calcif. Tissue Res.
(1974)

There are more references available in the full text version of this article.

Cited by (182)

Predicting trabecular arrangement in the proximal femur: An artificial neural network approach for varied geometries and load cases
2023, Journal of Biomechanics
Machine learning (ML) and deep learning (DL) approaches can solve the same problems as the finite element method (FEM) with a high degree of accuracy in a fraction of the required time, by learning from previously presented data.
In this work, the bone remodelling phenomenon was modelled using feed-forward neural networks (NN), by gathering a dataset of density distribution comprising several geometries and load cases. The model should output for some point in the domain the its apparent density, taking into consideration the geometric and loading parameters of the model . After training. the trabecular distribution obtained with the NN was similar to the FEM while the analysis was performed in a fraction of the time, having shown a reduction from 1020 s to 0.064 s. It is expected that the results can be extended to different structures if a different dataset is acquired. In summary, the ML approach allows for significant savings in computational time while presenting accurate results.
Feasibility of additively manufacturing synthetic bone for sports personal protective equipment applications
2023, Annals of 3D Printed Medicine
Human limb surrogates, of varying biofidelity, are used in the performance assessment of sports personal protective equipment (PPE). Such biofidelic surrogates have incorporated soft tissue simulants (silicones) and synthetic bone (short fibre filled epoxy). Testing surrogates incorporating realistic synthetic bone could help to further our knowledge of fracture trauma mechanics, and applications such as the effectiveness of sports PPE. Limb surrogates with embedded synthetic bone are rarely tested to fracture, mainly due to the effort and cost of replacing them. This paper proposes additive manufacturing of synthetic bones, with appropriate bone like fracture characteristics, potentially making them more accessible and cost effective. A Markforged® X7™ printer was used as it prints a base filament (Onyx™) alongside a continuous strand of reinforcement (e.g., carbon fibre). The properties of specimens from this printer vary with the type, volume fraction and position of reinforcement. Bar specimens (10 × 4 × 120 mm) with varying amounts of carbon fibre reinforcement were printed for three-point bend testing to determine the feasibility of achieving mechanical properties close to compact bone (bending modulus of ∼15 GPa, bending strength of ∼180 MPa). Bending strength for the various bar specimens ranged from 32 to 378 MPa, and modulus values ranged from 1.5 to 25.8 GPa. Based on these results, four 140 mm long oval shaped cylindrical specimens of ø14 and ø16 mm were printed to represent a basic radius bone model. Three-point bend testing of these bone models showed similar bending modulus (3.8 to 5.3 GPa vs. 3.66 to 14.8 GPa) to radius bones reported in the literature, but higher bending strength (147 to 200 MPa vs. 80.31 ± 14.55 MPa).
Biomechanical behavior of PMMA 3D printed biomimetic scaffolds: Effects of physiologically relevant environment
2023, Journal of the Mechanical Behavior of Biomedical Materials
Citation Excerpt :
The IWP groups showed substantially higher flexural stiffness (range: 10–71%) and strength (range: 24–72%) when compared with the Primitive specimens of similar as-designed wall-thickness (Fig. 3E–F). In this current study, 3D printed TPMS PMMA-microfilled scaffolds showed flexural stiffness values (Primitive: 160–660 N/mm and IWP: 170–1200 N/mm) within the lower limit of those previously reported for human bone (300–2500 N/mm) (Lotz et al., 1991; Yeh et al., 2019). Fracture mechanisms of the studied 3D printed scaffolds were observed to involve core yielding and buckling, top face sheet compression failure, and bottom face sheet tension failure (Fig. 5).
Functional cellular structures with controllable mechanical and morphological properties are of great interest for applications including tissue engineering, energy storage, and aerospace. Additive manufacturing (AM), also referred to as 3D printing, has enabled the potential for fabrication of functional porous scaffolds (i.e., meta-biomaterials) with controlled geometrical, morphological, and mechanical properties. Understanding the biomechanical behavior of 3D printed porous scaffolds under physiologically relevant loading and environmental conditions is crucial in accurately predicting the in vivo performance. This study was aimed to investigate the environmental dependency of the mechanical responses of 3D printed porous scaffolds of poly(methyl methacrylate) (PMMA) Class IIa biomaterial that was based on triply periodic minimal surfaces – TPMS (i.e., Primitive and Schoen-IWP). The 3D printed scaffolds (n = 5/study group) were tested under compressive loading in both ambient and fluidic (distilled water with pH = 7.4) environments according to ASTM D1621 standards. Outcomes of this study showed that compressive properties of the developed scaffolds are significantly lower in the fluidic condition than the ambient environment for the same topological and morphological group ( $p \leq 0.023$ ). Additionally, compressive properties and flexural stiffness of the studied scaffolds were within the range of trabecular bone's properties, for both topological classes. Relationships between predicted mechanical responses and morphological properties (i.e., porosity) were evaluated for each topological class. Quantitative correlation analysis indicated that mechanical behavior of the developed 3D printed scaffolds can be controlled based on both topology and morphology.
Simple anisotropic model of Bone Adaptation - SAMBA
2022, Journal of the Mechanical Behavior of Biomedical Materials
Bone presents the ability to adapt itself to the evolving mechanical environment. A simple anisotropic model for bone adaptation allowing reproducing the evolution of the elastic properties and the reorientation of the anisotropy frame is proposed is this work. The elastic properties are related to the value of the bone apparent density. The evolution law of the density is described via two functions reflecting the activities of the osteoclast and osteoblast cells. The anisotropy of the elastic properties of the bone is assumed evolving continuously between those of trabecular and compact tissues. The existence of a target material frame is assumed to describe its reorientation. The rate of rotation or spin of the material frame is supposed to be proportional to the target orientation angle and to the activity of the osteoclasts and osteoblasts. The mechanical stimulus governing the evolution of the apparent density is defined as the ratio between the current strain energy density and its critical value corresponding to the initiation of bone damage. The simulations showed that this simple model can reproduce some essential phenomena observed during bone adaptation process.
Subject specific finite element modelling of periprosthetic femoral fractures in different load cases
2022, Journal of the Mechanical Behavior of Biomedical Materials
Periprosthetic femoral fractures (PFF) around total hip replacements are one of the biggest challenges for orthopaedic surgeons. To understand the risk factors and formation of these fractures, the development of a reliable finite element (FE) model incorporating bone failure is essential. Due to the anisotropic and complex hierarchical structure of bone, the mechanical behaviour under large strains is difficult to predict. In this study, a state-of-the-art subject specific FE modelling technique for bone is utilised to generate and investigate PFF. A bilinear constitutive law is applied to bone tissue in subject specific FE models of five human femurs which are virtually implanted with a straight hip stem to numerically analyse PFF. The material parameters of the models are expressed as a function of bone ash density and mapped node wise to the FE mesh. In this way the subject specific, heterogeneous structure of bone is mimicked. For material mapping of the parameters, computed tomography (CT) images of the original fresh-frozen femurs are used. Periprosthetic fractures are generated by deleting elements on the basis of a critical plastic strain failure criterion. The models are analysed under physiological and clinically relevant conditions in two different load cases re-enacting stumbling and a sideways fall on the hip. The results of the analyses are quantified with experimental data from previous work. With regard to fracture pattern, stiffness and failure load the simulations of the load case stumbling delivered the most stable and accurate results. In general, mapping of material properties was found to be an appropriate way to reproduce PFF with finite element models.
Limit analysis of human proximal femur
2021, Journal of the Mechanical Behavior of Biomedical Materials
A limit analysis numerical approach oriented to predict the peak/collapse load of human proximal femur, under two different loading conditions, is presented. A yield criterion of Tsai–Hu-type, expressed in principal stress space, is used to model the orthotropic bone tissues. A simplified human femur 3D model is envisaged to carry on numerical simulation of in-vitro tests borrowed from the relevant literature and to reproduce their findings. A critical discussion, together with possible future developments, is presented.

View all citing articles on Scopus

^∗: Current address: Failure Analysis Associated, 149 Commonwealth Dr., Menlo Park, CA 94025, U.S.A.

View full text

Mechanical properties of metaphyseal bone in the proximal femur

Abstract

J. Biomechanics

J. Biomechanics

The apparent elastic modulus of the juxtarticular subchondral bone of the femoral head

J. Orthop. Res.

Aging of bone tissue: mechanical properties

J. Bone Jt Surg. (Am)

The elastic modulus of trabecular, subchondral, and cortical bone tissue

Trans. 35th ORS

The mechanical properties of cortical bone tissue

Tensile yield in bone

Calcif. Tissue Res.