Abstract
A mathematical model has been established to predict the formation of macrosegregation for a unidirectional solidification of aluminum-copper alloys cooled from the bottom. The model, based on the continuum formulation, allows the calculation of transient distributions of temperature, velocity, and species in the solidifying alloy caused by thermosolutal convection and shrinkage-induced fluid flow. Positive segregation in the casting near the bottom (inverse segregation) is found, which is accompanied by a moving negative-segregated mushy zone. The effects of shrinkage-induced fluid flow and solute diffusion on the formation of macrosegregation are examined. It is found that the redistribution of solute in the solidifying alloy is caused by the flow of solute-rich liquid in the mushy zone due to solidification shrinkage. A higher heat-extraction rate at the bottom increases the solidification rate, decreasing the size of the mushy zone, reducing the flow of solute-rich liquid in the mushy zone and, as a result, lessening the severity of inverse segregation. Comparisons between the theoretical predictions from the present study and previous modeling results and available experimental data are made, and good agreements are obtained.
Similar content being viewed by others
Abbreviations
- c :
-
specific heat
- C :
-
coefficient, defined in Eq. [9]
- c l :
-
permeability coefficient, defined in Eq. [8]
- d :
-
dendrite arm spacing
- D :
-
mass-diffusion coefficient
- f :
-
mass fraction
- g :
-
volume fraction or gravitational acceleration
- h :
-
enthalpy
- H :
-
latent heat
- k :
-
thermal conductivity
- k p :
-
equilibrium partition ratio
- K :
-
permeability
- p :
-
pressure
- t :
-
time
- T :
-
temperature
- T m :
-
fusion temperature at zero solute concentration
- u :
-
velocity in thex-direction
- v :
-
velocity in they-direction V velocity vector Vr relative velocity vector (Vl — Vs)
- x, y :
-
Cartesian coordinates
- β S :
-
solutal expansion coefficient
- β T :
-
thermal expansion coefficient
- ε:
-
rate of temperature change
- μ:
-
dynamic viscosity
- ρ:
-
density
- 0:
-
initial value
- c :
-
chill
- e :
-
eutectic
- l :
-
liquid phase
- m :
-
fusion
- r :
-
relative to solid velocity
- s :
-
vsolid phase
- α :
-
constituent of alloy
References
M.C. Flemings:Solidification Processing, McGraw-Hill, Inc., New York, NY, 1974, pp. 214–58.
K.M. Fisher:PCH, PhysicoChem. Hydrodyn., 1981, vol. 2, pp. 311–26.
E. Scheil:Metallforschung, 1947, vol. 2, pp. 69–75.
J.S. Kirkaldy and W.V. Youdelis:Trans. TMS-AIME, 1958, vol. 212, pp. 833–40.
M.C. Flemings and G.E. Nereo:Trans. TMS-AIME, 1967, vol. 239, pp. 1449–61.
M.C. Flemings, R. Mehrabian, and G.E. Nereo:Trans. TMS-AIME, 1968, vol. 242, pp. 41–49.
M.C. Flemings and G.E. Nereo:Trans. TMS-AIME, 1968, vol. 242, pp. 50–55.
H. Kato and J.R. Cahoon:Metall. Trans. A, 1985, vol. 16A, pp. 579–87.
I. Ohnaka and M. Matsumoto:Tetsu-to-Hagané (J. Iron Steel Inst. Jpn.), 1987, vol. 73, pp. 1698–1705.
I. Ohnaka and M. Matsumoto:Trans. Iron Steel Inst. Jpn., 1986, vol. 26, pp. 781–89.
W.D. Bennon and F.P. Incropera:Int. J. Heat Mass Transfer, 1987, vol. 30, pp. 2161–70.
W.D. Bennon and F.P. Incropera:Int. J. Heat Mass Transfer, 1987, vol. 30, pp. 2171–87.
C. Beckermann and R. Viskanta:PCH, PhysicoChem. Hydrodyn., 1988, vol. 10, pp. 195–213.
D.G. Neilson and F.P. Incropera:Int. J. Heat Mass Transfer, 1991, vol. 34, pp. 1717–32.
K.C. Chiang and H.L. Tsai:Int. J. Heat Mass Transfer, 1992, vol. 35, pp. 1763–70.
K.C. Chiang and H.L. Tsai:Int. J. Heat Mass Transfer, 1992, vol. 35, pp. 1771–78.
P.C. Carman:Trans. Inst. Chem. Eng., 1937, vol. 15, pp. 150–66.
K. Kubo and R.D. Pehlke:Metall. Trans. B, 1985, vol. 16B, pp. 359–66.
G.S. Beavers and E.M. Sparrow:J. Appl. Mech., 1969, vol. 36, pp. 711–14.
J. Ni and C. Beckermann:Transport Phenomena in Material Processing, M. Charmichi, M.K. Chyu, Y. Joshi, and S.M. Walsh, eds., ASME HTD, Fairfield, NJ, 1990, vol. 32, pp. 45–56.
S.V. Patankar:Numerical Heat Transfer and Fluid Flow, Hemisphere. New York, NY, 1980, pp. 96–102.
K.C. Chiang: Ph.D. Thesis, University of Missouri-Rolla, Rolla, MO, 1990.
R.D. Pehlke, A. Jeyarajan, and H. Wada:Summary of Thermal Properties for Casting Alloys and Mold Materials, Report No. PB83-211003, National Technical Information Service, Washington, DC, 1983, pp. 81-93.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Diao, Q.Z., Tsai, H.L. Modeling of solute redistribution in the mushy zone during solidification of aluminum-copper alloys. Metall Trans A 24, 963–973 (1993). https://doi.org/10.1007/BF02656518
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF02656518