Abstract
Hip fracture has become a common health problem among old people. Understanding hip fracture mechanics is the first step to effectively prevent hip fracture. The objective of this study was to investigate the combined effect of reversed stress/strain patterns in femur (during single-leg stance and sideways fall) and the inhomogeneous material properties of femur bone. We constructed 40 subject-specific femur finite element models from medical quantitative computed tomography and used them to identify high risk regions in the femur induced by the two loading configurations. The obtained results showed that compared to the single-leg stance, in the sideways fall the highest stress and strain occurred at different locations; and the tensile-compressive stress status was also completely reversed. Previous studies have found that a bone has different strength at different anatomic sites, and at the same site it has different compressive and tensile strength. Our study suggested that, in addition to the large magnitude of impact force induced in falling, the abnormal stress/strain patterns produced by the non-habitual loading condition in falling may be another external contributor to hip fracture.
Similar content being viewed by others
References
Resnick, N. M., & Greenspan, S. L. (1989). ‘Senile’ osteoporosis reconsidered. JAMA, 261, 1025–1029.
Keyak, J. H., Rossi, S. A., Jones, K. A., Les, C. M., & Skinner, H. B. (2001). Prediction of fracture location in the proximal femur using finite element models. Medical Engineering & Physics, 23, 657–664.
Dragomir-Daescu, D., Op Den Buijs, J., McEligot, S., Dai, Y. F., Entwistle, R. C., Salas, C., et al. (2011). Robust QCT/FEA models of proximal femur stiffness and fracture load during a sideways fall on the hip. Annals of Biomedical Engineering, 39(2), 742–755.
Mirzaei, M., Keshavarzian, M., & Naeini, V. (2014). Analysis of strength and failure pattern of human proximal femur using quantitative computed tomography (QCT)-based finite element method. Bone, 64, 108–114.
Bessho, M., Ohnishi, I., Matsumoto, T., Ohashi, S., Matsuyama, J., Tobita, K., et al. (2009). Prediction of proximal femur strength using a CT-based nonlinear finite element method: Differences in predicted fracture load and site with changing load and boundary conditions. Bone, 45, 226–231.
Koivumäki, J. E. M., Thevenot, J., Pulkkinen, P., Kuhn, V., Link, T. M., Eckstein, F., et al. (2012). CT-based finite element models can be used to estimate experimentally measured failure loads in the proximal femur. Bone, 50, 824–829.
Michelson, J. D., Myers, A., Jinnah, R., Cox, Q., & Van Natta, M. (1995). Epidemiology of hip fractures among the elderly: Risk factors for fracture type. Clinical Orthopaedics and Related Research, 311, 129–135.
Keyak, J. H., Meagher, J. M., Skinner, H. B., & Mote, C. D., Jr. (1990). Automated three-dimensional finite element modelling of bone: A new method. Journal of Biomedical Engineering, 12, 389–397.
Keaveny, T. M., Borchers, R. E., Gibson, L. J., & Hayes, W. C. (1993). Trabecular bone modulus and strength can depend on specimen geometry. Journal of Biomechanics, 26, 991–1000.
Les, C. M., Keyak, J. H., Stover, S. M., Taylor, K. T., & Kaneps, A. J. (1994). Estimation of material properties in the equine metacarpus with use of quantitative computed tomography. Journal of Orthopaedic Research, 12, 822–833.
Keller, T. S. (1994). Predicting the compressive mechanical behavior of bone. Journal of Biomechanics, 27, 1159–1168.
Yosibash, Z., Tal, D., & Trabelsi, N. (2010). Predicting the yield of the proximal femur using high-order finite-element analysis with inhomogeneous orthotropic material properties. Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences, 368, 2707–2723.
Keyak, J. H., Rossi, S. A., Jones, K. A., & Skinner, H. B. (1997). Prediction of femoral fracture load using automated finite element modeling. Journal of Biomechanics, 31(2), 125–133.
Reilly, D. T., & Burstein, A. H. (1975). The elastic and ultimate properties of compact bone tissue. Journal of Biomechanics, 8, 393–405.
Yoshikawa, T., Turner, C. H., Peacock, M., Slemenda, C. W., Weaver, C. M., Teegarden, D., et al. (1994). Geometric structure of the femoral neck measured using dual-energy x-ray absorptiometry. Journal of Bone and Mineral Research, 9(7), 1053–1064.
Nishiyama, K. K., Gilchrist, S., Guy, P., Cripton, P., & Boyd, S. K. (2013). Proximal femur bone strength estimated by a computationally fast finite element analysis in a sideways fall configuration. Journal of Biomechanics, 46, 1231–1236.
Robinovitch, S. N., Hayes, W. C., & McMahon, T. A. (1991). Prediction of femoral impact forces in falls on the hip. Journal of Biomechanical Engineering, 113, 366–374.
Kim, J. S., Park, T. S., Park, S. B., Kim, J. S., Kim, I. Y., & Kim, S. I. (2000). Measurement of femoral neck anteversion in 3D. Part 1: 3D imaging method. Med. Biol. Eng. Comput., 38, 603–609.
Atilla, B., Oznur, A., Caglar, O., Tokgozoglu, M., & Alpaslan, M. (2007). Osteometry of the femora in Turkish individuals: A morphometric study in 114 cadaveric femora as an anatomic basis of femoral component design. Acta Orthop. Traumatol. Turc., 41, 64–68.
Sariali, E., Mouttet, A., Pasquier, G., & Durante, E. (2009). Three-dimensional hip anatomy in osteoarthritis: Analysis of the femoral offset. Journal of Arthroplasty, 24, 990–997.
Kheirollahi, H., & Luo, Y. (2015). Assessment of hip fracture risk using cross-section strain energy by QCT-based finite element modeling. BioMed Research International, 2015, Article ID 413839.
Kheirollahi, H., & Luo, Y. (2015). Identification of high stress and strain regions in proximal femur during single-leg stance and sideways fall using QCT-based finite element model. International Journal of Medical, Health, Biomedical, Bioengineering and Pharmaceutical Engineering, 9(8), 541–548.
Nikander, R., Kannus, P., Dastidar, P., Hannula, M., Harrison, L., Cervinka, T., et al. (2009). Targeted exercises against hip fragility. Osteoporosis International, 20, 1321–1328.
Abrahamsen, B., van Staa, T., Ariely, R., Olson, M., & Cooper, C. (2009). Excess mortality following hip fracture: A systematic epidemiological review. Osteoporosis International, 20, 1633–1650.
Wolff, J. (1986). The law of bone remodeling (translation of the German 1892 edition). Berlin: Springer.
Frost, H. M. (1994). Wolff’s law and bone’s structural adaptations to mechanical usage: An overview for clinicians. The Angle Orthodontist, 64, 175–188.
Røhl, L., Larsen, E., Linde, F., Odgaard, A., & Jørgensen, J. (1991). Tensile and compressive properties of cancellous bone. Journal of Biomechanics, 24, 1143–1149.
Bayraktar, H. H., Morgan, E. F., Niebur, G. L., Morris, G. E., Wong, E. K., & Keaveny, T. M. (2004). Comparison of the elastic and yield properties of human femoral trabecular and cortical bone tissue. Journal of Biomechanics, 37, 27–35.
de Bakker, P. M., Manske, S. L., Ebacher, V., Oxland, T. R., Cripton, P. A., & Guy, P. (2009). During sideways falls proximal femur fractures initiate in the superolateral cortex: Evidence from high-speed video of simulated fractures. Journal of Biomechanics, 42, 1917–1925.
Acknowledgements
The reported research was supported by the Natural Sciences and Engineering Research Council (NSERC) and Research Manitoba of Canada, which are gratefully acknowledged.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
There is no conflict of interest involved in the reported study or in the published results.
Ethical approval
The QCT images used in this study were acquired from Health Science Centre located at Winnipeg under an Ethical Approval issued by the Research Ethics Board (REB) of the University of Manitoba.
Rights and permissions
About this article
Cite this article
Kheirollahi, H., Luo, Y. Understanding Hip Fracture by QCT-Based Finite Element Modeling. J. Med. Biol. Eng. 37, 686–694 (2017). https://doi.org/10.1007/s40846-017-0266-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40846-017-0266-9