Skip to main content
Log in

Linear thermal expansion, thermal ageing, relaxations and post-cure of thermoset polymer composites using modulated temperature thermomechanometry

  • Published:
Journal of Thermal Analysis and Calorimetry Aims and scope Submit manuscript

Abstract

The glass transition temperature (Tg) regions of polymers and composites were studied using static force thermomechanometry and modulated temperature thermomechanometry (mT-TM). Modulated temperature allowed measurement of linear thermal expansion coefficient and glass transition as reversing phenomena, independent of any residual cure and relaxations that are non-reversing in nature. The reversing dimension change curves were well defined with continuous expansion that increased after Tg, though sensitivity decreased with crosslinking and fibre content. The non-reversing dimension change curves showed the maximum variation and revealed complex changes, and the non-reversing characteristics were confirmed by repeated scans, both upon cooling or re-heating. Non-reversing curves showed contractions with increasing temperature. Lissajous figures demonstrated that temperature modulation deviated significantly from linear response in the temperature range below Tg, and during the Tg range, steady state was not maintained. Measurements made in mT-TM mode were compared with modulated force TM where Tg was revealed as a peak in loss modulus or tan(δ), whilst reversing events were consistent with changes in storage modulus.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13

Similar content being viewed by others

References

  1. Van Assche G, Van Hemelrijck A, Rahier H, Van Mele B. Modulated differential scanning calorimetry: non-isothermal cure, vitrification, and devitrification of thermosetting systems. Thermochim Acta. 1996;286:209–24.

    Article  Google Scholar 

  2. Dao B, Hodgkin J, Krstina J, Mardel J, Tian WJ. Accelerated aging versus realistic aging in aerospace composite materials. V. The effects of hot/wet aging in a structural epoxy composite. Appl Polym Sci. 2010;115:901–10.

    Article  CAS  Google Scholar 

  3. Gahleitner M, Grein C, Bernreitner K, Knogler B, Hebesberger E. The use of DMTA for predicting standard mechanical properties of developmental polyolefins. J Thermal Anal Cal. 2009;98:623–8.

    Article  CAS  Google Scholar 

  4. Xie M, Zhang Z, Gu Y, Li M, Su Y. A new method to characterize the cure state of epoxy prepreg by dynamic mechanical analysis. Thermochim Acta. 2009;487:8–17.

    Article  CAS  Google Scholar 

  5. Shepard DD, Twombly B. Simultaneous dynamic mechanical analysis and dielectric analysis of polymers. Thermochim Acta. 1996;272:125–9.

    Article  CAS  Google Scholar 

  6. Hutchinson J. Determination of the glass transition temperature. J Therm Anal Cal. 2009;98:579–89.

    Article  CAS  Google Scholar 

  7. Yazdi M, Lee-Sullivan P. Determination of dual glass transition temperatures of a PC/ABS blend using two TMA modes. J Therm Anal Cal. 2009;96:7–14.

    Article  CAS  Google Scholar 

  8. Price DM. Method and apparatus for modulated-temperature thermomechanical analysis, TA Instruments, New Castle. US Patent 6,007,240;1999.

  9. Price DM. Modulated temperature thermomechanical measurements. In: Riga AT, Judovits LH, editors. Materials characterization by dynamic and modulated thermal analytical techniques, ASTM STP 1402. 2001:103–114.

  10. Lange J, Manson J-AE, Hult A. Build-up of structure and viscoelastic properties in epoxy and acrylate resins cured below their ultimate glass transition temperature. Polymer. 1996;37:5859–68.

    Article  CAS  Google Scholar 

  11. Kim YK, White SR. Stress relaxation behavior of 3501–6 epoxy resin during cure. Polym Eng Sci. 1996;36:2852–62.

    Article  CAS  Google Scholar 

  12. Price DM. Modulated-temperature thermomechanical analysis. Thermochim Acta. 2000;357–358:23–9.

    Article  Google Scholar 

  13. Wurm A, Merzlyakov M, Schick C. Temperature modulated dynamic mechanical analysis. Thermochim Acta. 1999;330:121–30.

    Article  CAS  Google Scholar 

  14. Takegawa K, Fukao K, Saruyama Y. Aging effects on the thermal expansion coefficient and the heat capacity of glassy polystyrene studied with simultaneous measurement using temperature modulation technique. Thermchimica Acta. 2007;461:67–71.

    Article  CAS  Google Scholar 

  15. Kociba K. Temperature calibration of TMAs using modulated temperature and Curie temperature reference standards. J Therm Anal Cal. 2000;60:779–84.

    Article  CAS  Google Scholar 

  16. Li G, Lee-Sullivan P, Thring RW. Determination of activation energy for glass transition of an epoxy adhesive using dynamic mechanical analysis. J Therm Anal Cal. 2000;60:377–90.

    Article  CAS  Google Scholar 

Download references

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Robert A. Shanks.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Shanks, R.A. Linear thermal expansion, thermal ageing, relaxations and post-cure of thermoset polymer composites using modulated temperature thermomechanometry. J Therm Anal Calorim 106, 151–158 (2011). https://doi.org/10.1007/s10973-011-1684-5

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10973-011-1684-5

Keywords

Navigation