Summary
The deformation and flow properties of solid polymers under uniaxial tensile and compressive loading have been determined for a variety of both crystalline and amorphous polymers at hydrostatic pressures to about 7 , kb. For some polymers, like polytetrafluoroethylene, cold drawing is inhibited by increasing pressure, and scanning electron micrographs show that local plastic deformation is greatly reduced. However, the true flow stress and the true fracture stress both increase with pressure, as does, also, the elastic modulus. The increase is greatest in the low-pressure range below 2 kb. This behavior is attributed to the pressure-induced shifting of a lowtemperatureβ′-transition. The influence of polymer composition and of the initial elastic constants on the pressure dependence of the elastic modulus and the yield stress is discussed. The observed behavior can be analyzed in terms of finite strain effects and a pressure-dependent yield criterion. It is shown that some amorphous polymers undergo a pressure-induced brittle-ductile transition, and these findings are used to explore the hydrostatic extrusion of polyimide and polysulfone at room temperature.
Zusammenfassung
Die Deformation und Fließeigenschaften fester Polymerer unter uniaxialer Spannung und unter Druck wurden für eine Serie von kristallinen wie amorphen Polymeren bei Drucken bis 7 kb gemessen. Für einige Polymere, wie das Polytetrafluoräthylen, wird Kaltverstreckung bei steigendem Druck ausgelöst und Elektroscanning-Bilder zeigen, daß die örtliche plastische Deformation stark reduziert ist. Die wahre Fließspannung und Bruchspannung jedoch steigen beide mit dem Druck, ebenso der Elastizitätsmodul. Der Anstieg ist am größten im niedrigen Druckbereich unter 2kb. Dieses Verhalten ist einer durch den Druck initiierten Verlagerung einer Tief-temperatur-β′-Umwandlung zuzuschreiben. Der Einfluß der Polymerkomposition und der anfangs elastischen Konstanten auf die Druckabhängigkeit des elastischen Moduls und der Fließspannung wird diskutiert. Das beobachtete Verhalten läßt sich in Termen der Enddehnungseffekte und einem druckabhängigen Fließkriterium diskutieren. Es wird gezeigt, daß einige amorphe Polymere eine durch den Druck ausgelöste spröd-duktil-Umwandlung erfahren. Und diese Feststellungen wurden verwendet, die hydrostatische Extrusion von Polyimid und Polysulfon bei Raumtemperatur zu erklären.
Similar content being viewed by others
References
Bridgman, P. W., The Physics of High Pressure, (New York 1970); Studies in Large Plastic Flow and Fracture, (London 1952).
Bereshev, B. I., L. F. Vereshchagin, Y. N. Ryabinin andL. D. Livshits, Some Problems of Large Plastic Deformation at High Pressure (London-New York 1963).
Pugh, H. L. D., Mechanical Behavior of Materials under Pressure, (Amsterdam 1970).
Radcliffe, S. V., in:H. H. Kausch, J. A. Hassell andR. I. Jaffee), (Ed.), Deformation and Fracture of High Polymers, p. 191, (London-New York 1972).
Sauer, J. A., K. D. Pae andS. K. Bhateja, J. Macromol. Sci.-Phys.B8 (4), 649 (1973).
Pugh, H. L. D., E. F. Chandler, L. Holliday andJ. Mann, Polymer Eng. Sci.11, 463 (1971).
Christiansen, A. W., E. Baer andS. V. Radcliffe, Phil. Mag.24, 451 (1971).
Sauer, J. A., D. R. Mears andK. D. Pae, European Polymer J.6, 1015 (1970).
Rabinowitz, S., I. M. Ward, andJ. S. C. Parry, J. Mat. Sci.5, 29 (1970).
Ainbinder, S. B., M. G. Laka andI. Y. Maiors, Mekh. Polim.1, 65 (1965).
Biglione, G., E. Baer andS. V. Radcliffe, in: P. L. Pratt et al.), (Ed.), Fracture — 1969, p. 520, (1969).
Sauer, J. A., S. K. Bhateja andK. D. Pae, Proc. 3rd Inter-American Conf. on Materials Technology, p. 486, Rio de Janeiro, 1972.
Bhateja, S. K. andK. D. Pae, Polymer Letters10, 531 (1972).
Bhateja, S. K., K. D. Pae andJ. A. Sauer, J. Appl. Polymer Science18, 1319 (1974).
Pae, K. D., S. K. Bhateja andJ. A. Sauer, Preprints IUPAC Intern. Symp. Macromolecules, Helsinki4, III-48 (1972).
Pae, K. D., S. K. Bhateja andJ. A. Sauer, Proc. 1st Intern. Conf. on Hydrostatic Extrusion, Sterling (1973) (to be published).
Laka, M. G. andA. A. Dzenis, Mekh. Polim.3, 1043 (1967).
Vroom, V. I. andR. F. Westover, SPE Journal25, 58 (1969).
Marin, J., Engineering Materials, (Englewood Cliffs 1952).
Alksne, K. I., Mekh. Polim.3, 1018 (1967).
Sardar, D., S. V. Radcliffe andE. Baer, Polymer Eng. Sci.8, 290 (1968).
Weir, C. E., J. Res. NBS50, 95 (1951);53, 245 (1954).
Flack, H. D., J. Polymer Sci. PartA-2, 10, 1799 (1972).
Miyakawa, S. andT. Takemura, Japan. J. Appl. Phys.7, 814 (1968).
Takayanagi, M., Pure Appl. Chem.23, 183 (1970).
Mears, D. R., K. D. Pae andJ. A. Sauer, J. Appl. Phys.40, 4229 (1969).
Yoon, H. N., K. D. Pae andJ. A. Sauer, Bulletin APS, Ser. II,19, 352 (1974).
McCrum, N. G., B. E. Read andG. Williams, Anelastic and Dielectric Effects in Polymeric Solids, (London-New York 1967).
Passaghn, E. andG. M. Martin, J. Res. NBS,A68, 273 (1964).
Koppelmann, J. andJ. Gielessen, Kolloid Z.175, 97 (1961); Z. Elektrochem.65, 689 (1961).
Billinghurst, P. R. yndD. Tabor, Polymer12, 109 (1971).
Silano, A. A., S. K. Bhateja andK. D. Pae, Intern. J. Polymeric Mater3, 117 (1974).
Weaver, C. V. andM. S. Patterson, J. Polymer Sci., PartA-2, 7, 587 (1969).
Pae, K. D. andJ. A. Sauer, in: Engineering Solids under Pressure, (London 1971).
Murnaghan, F. D., Finite Deformations of an Elastic Solid, (New York 1951).
Birch, F., J. Appl. Phys.9, 4 (1938).
Warfield, R. V., J. E. Cuevas, andF. R. Barnet, J. Appl. Polymer Sci.12, 1147 (1968).
Bonnin, M., C. M. R. Dunn andS. Turner, Plastics and Polymers (Dec. 1969).
Rosen, B., Fracture Processes in Polymeric Solids, p. 60, (London-New York 1964).
Brydson, J. A., Plastic Materials, p. 349, (Amsterdam 1970).
Reported value for du Pont SP-1 polyimide.
Ghafelehbashi, M. andK. M. Koliwad, J. Appl. Phys.41, 4010 (1970).
Fritz, I. J., J. Appl. Phys.45, 60 (1974).
Sternstein, S. S. andL. Ongchin, ACS Polymer Preprints10, 117 (1969).
Bauwens, J. C., J. Polymer Sci.A-2, 5, 1145 (1967).
Bauwens-Crowet, C., J. Mat. Sci.8, 968 (1973).
Ree, T. andM. Eyring, in:Eirich, F. R. (Ed.), Rheology II (London-New York 1964).
Whitney W. andR. D. Andrews, J. Polymer Sci. C, No.16, 2981 (1967).
Hu, L. W. andK. D. Pae, J. Franklin Inst., p. 491 (June 1963).
Lim, T., V. Frosini, V. Zaleckas, D. Morrow, andJ. A. Sauer, Polymer Eng. Sci.13, 51 (1973).
Chung, C. andJ. A. Sauer, J. Polymer Sci. PartA-2, 9, 1097 (1971).
Buckley, A. andH. A. Long, Polymer Eng. Sci.9, 115 (1969).
Bhateja, S. K., Ph. D. dissertation (Rutgers University 1973).
Imada, K. andM. Takayanagi, Intern. J. Polymeric Mater.2, 89 (1973).
Author information
Authors and Affiliations
Additional information
With 16 figures and 3 tables
Rights and permissions
About this article
Cite this article
Sauer, J.A., Pae, K.D. The flow of solid polymers under high pressure. Colloid & Polymer Sci 252, 680–695 (1974). https://doi.org/10.1007/BF01554493
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF01554493